debian-installer_packages_po_sublevel1_da - en to da translation catalogue (11 entries)

note: Type: text Description :sl4:
en: Install the Arcboot boot loader on a hard disk
da: Installér opstartsindlæseren Arcboot på en harddisk

note: Type: string Description :sl4:
en: Disk for boot loader installation:
da: Disk hvorpå opstartsindlæseren skal installeres:

note: Type: string Description :sl4:
en: Arcboot must be installed into the volume header of a disk with a SGI disklabel. Usually the volume header of /dev/sda is used. Please give the device name of the disk on which to put arcboot.
da: Arcboot skal installeres i arkivhovedet på en disk med et SGI-diskmærkat. Normalt benyttes arkivhovedet /dev/sda. Angiv enhedsnavnet på den disk, hvorpå arcboot skal placeres.

note: Type: note Description :sl4:
en: Arcboot configured to use a serial console
da: Arcboot er sat op til at benytte en seriel konsol

note: Type: note Description :sl4:
en: Arcboot is configured to use the serial port ${PORT} as the console. The serial port speed is set to ${SPEED}.
da: Arcboot er sat op til at benytte den serielle port ${PORT} som konsol. Den serielle ports hastighed er sat til ${SPEED}.

note: Type: boolean Description :sl4:
en: Arcboot installation failed.  Continue anyway?
da: Kunne ikke installere arcboot. Fortsæt alligevel?

note: Type: boolean Description :sl4:
en: The arcboot package failed to install into /target/.  Installing Arcboot as a boot loader is a required step.  The install problem might however be unrelated to Arcboot, so continuing the installation may be possible.
da: Pakken arcboot kunne ikke installeres i /target/. Installationen af Arcboot er et obligatorisk trin. Installationsproblemet har dog muligvis intet med arcboot at gøre, og det fungerer muligvis alligevel hvis du fortsætter.

note: Type: note Description :sl4: Translators, the 4th string of this description has been dropped from PO files. It contains firmware commands and should not be translated.
en: Setting PROM variables for Arcboot
da: Sætter PROM-variable for Arcboot

note: Type: note Description :sl4: Translators, the 4th string of this description has been dropped from PO files. It contains firmware commands and should not be translated.
en: If this is the first Linux installation on this machine, or if the hard drives have been repartitioned, some variables need to be set in the PROM before the system is able to boot normally.
da: Hvis dette er den første Linuxinstallation på denne maskine, eller hvis harddiskene er blevet repartitioneret, er der nogle variabler i PROM'en, der skal sættes, før systemet er i stand til at opstarte normalt.

note: Type: note Description :sl4: Translators, the 4th string of this description has been dropped from PO files. It contains firmware commands and should not be translated. "Stop for Maintenance" should be left in English
en: At the end of this installation stage, the system will reboot.  After this, enter the command monitor from the "Stop for Maintenance" option, and enter the following commands:
da: Ved afslutningen af dette installationstrin, vil systemet genstarte. Derefter skal du gå ind i femte menupunkt, "Enter Command Monitor" fra punktet "Stop for Maintenance" og skrive følgende kommandoer:

note: Type: note Description :sl4: Translators, the 4th string of this description has been dropped from PO files. It contains firmware commands and should not be translated.
en: You will only need to do this once.  Afterwards, enter the "boot" command or reboot the system to proceed to your newly installed system.
da: Du behøver kun at gøre dette én gang. Giv derefter kommandoen "boot" eller genstart systemet for at gå videre til dit nyinstallerede system.
