ndisc6 0.9.4 - en to en translation catalogue (11 entries)

en: Cannot find user "%s"
en: Cannot find user “%s”

en: Cannot run "%s": %m
en: Cannot run “%s”: %m

en: Try "%s -h" for more information.
en: Try “%s -h” for more information.

en: Written by Pierre Ynard and Remi Denis-Courmont
en: Written by Pierre Ynard and Rémi Denis-Courmont

en: Copyright (C) %u-%u Pierre Ynard, Remi Denis-Courmont
en: Copyright © %u-%u Pierre Ynard, Rémi Denis-Courmont

en: Written by Remi Denis-Courmont
en: Written by Rémi Denis-Courmont

en: Copyright (C) %u-%u Remi Denis-Courmont
en: Copyright © %u-%u Rémi Denis-Courmont

en: Warning: "%s" is too small (%zu %s) to fill block of %zu %s.
en: Warning: “%s” is too small (%zu %s) to fill block of %zu %s.

en: 
      -4  force usage of the IPv4 protocols family
      -6  force usage of the IPv6 protocols family
      -b  specify the block bytes size (default: 1024)
      -d  wait for given delay (usec) between each block (default: 0)
      -e  perform a duplex test (TCP Echo instead of TCP Discard)
      -f  fill sent data blocks with the specified file content
      -h  display this help and exit
      -n  specify the number of blocks to send (default: 100)
      -V  display program version and exit
      -v  enable verbose output
en: 
      -4  force usage of the IPv4 protocols family
      -6  force usage of the IPv6 protocols family
      -b  specify the block bytes size (default: 1024)
      -d  wait for given delay (µsec) between each block (default: 0)
      -e  perform a duplex test (TCP Echo instead of TCP Discard)
      -f  fill sent data blocks with the specified file content
      -h  display this help and exit
      -n  specify the number of blocks to send (default: 100)
      -V  display program version and exit
      -v  enable verbose output

en: 
      -A  send TCP ACK probes
      -d  enable socket debugging
      -E  set TCP Explicit Congestion Notification bits in probe packets
      -f  specify the initial hop limit (default: 1)
      -g  insert a route segment within a "Type 0" routing header
      -h  display this help and exit
      -i  force outgoing network interface
      -l  set probes byte size
      -m  set the maximum hop limit (default: 30)
      -N  perform reverse name lookups on the addresses of every hop
      -n  don't perform reverse name lookup on addresses
      -p  override source TCP port
      -q  override the number of probes per hop (default: 3)
      -r  do not route packets
      -S  send TCP SYN probes (default)
      -s  specify the source IPv6 address of probe packets
      -t  set traffic class of probe packets
      -V, --version  display program version and exit
      -w  override the timeout for response in seconds (default: 5)
      -z  specify a time to wait (in ms) between each probes (default: 0)
en: 
      -A  send TCP ACK probes
      -d  enable socket debugging
      -E  set TCP Explicit Congestion Notification bits in probe packets
      -f  specify the initial hop limit (default: 1)
      -g  insert a route segment within a “Type 0” routing header
      -h  display this help and exit
      -i  force outgoing network interface
      -l  set probes byte size
      -m  set the maximum hop limit (default: 30)
      -N  perform reverse name lookups on the addresses of every hop
      -n  don’t perform reverse name lookup on addresses
      -p  override source TCP port
      -q  override the number of probes per hop (default: 3)
      -r  do not route packets
      -S  send TCP SYN probes (default)
      -s  specify the source IPv6 address of probe packets
      -t  set traffic class of probe packets
      -V, --version  display program version and exit
      -w  override the timeout for response in seconds (default: 5)
      -z  specify a time to wait (in ms) between each probes (default: 0)

en: 
      -A  send TCP ACK probes
      -d  enable socket debugging
      -E  set TCP Explicit Congestion Notification bits in TCP packets
      -f  specify the initial hop limit (default: 1)
      -g  insert a route segment within a "Type 0" routing header
      -h  display this help and exit
      -I  use ICMPv6 Echo Request packets as probes
      -i  force outgoing network interface
      -l  display incoming packets hop limit
      -m  set the maximum hop limit (default: 30)
      -N  perform reverse name lookups on the addresses of every hop
      -n  don't perform reverse name lookup on addresses
      -p  override destination port
      -q  override the number of probes per hop (default: 3)
      -r  do not route packets
      -S  send TCP SYN probes
      -s  specify the source IPv6 address of probe packets
      -t  set traffic class of probe packets
      -U  send UDP probes (default)
      -V  display program version and exit
      -w  override the timeout for response in seconds (default: 5)
      -z  specify a time to wait (in ms) between each probes (default: 0)
en: 
      -A  send TCP ACK probes
      -d  enable socket debugging
      -E  set TCP Explicit Congestion Notification bits in TCP packets
      -f  specify the initial hop limit (default: 1)
      -g  insert a route segment within a “Type 0” routing header
      -h  display this help and exit
      -I  use ICMPv6 Echo Request packets as probes
      -i  force outgoing network interface
      -l  display incoming packets hop limit
      -m  set the maximum hop limit (default: 30)
      -N  perform reverse name lookups on the addresses of every hop
      -n  don’t perform reverse name lookup on addresses
      -p  override destination port
      -q  override the number of probes per hop (default: 3)
      -r  do not route packets
      -S  send TCP SYN probes
      -s  specify the source IPv6 address of probe packets
      -t  set traffic class of probe packets
      -U  send UDP probes (default)
      -V  display program version and exit
      -w  override the timeout for response in seconds (default: 5)
      -z  specify a time to wait (in ms) between each probes (default: 0)
