debian-installer_packages_po_sublevel1_bs - en to bs translation catalogue (25 entries)

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: ctc: Channel to Channel (CTC) or ESCON connection
bs: ctc: Channel to Channel (CTC) ili ESCON konekcija

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: iucv: Inter-User Communication Vehicle - available for VM guests only
bs: iucv: Inter-User Communication Vehicle - dostupno samo za VM goste

note: Type: select Description :sl5:
en: Network device type:
bs: Tip mrežnog uređaja:

note: Type: select Description :sl5:
en: Please choose the type of your primary network interface that you will need for installing the Debian system (via NFS or HTTP). Only the listed devices are supported.
bs: Molim odaberite tip Vašeg primarnog mrežnog interfejsa koji ćete trebati za instaliranje Debian sistema (preko NFS ili HTTP). Podržani su samo navedeni uređaji.

note: Type: select Description :sl5:
en: CTC read device:
bs: CTC uređaj za čitanje:

note: Type: select Description :sl5:
en: The following device numbers might belong to CTC or ESCON connections.
bs: Sljedeći brojevi uređaja mogu pripadati CTC ili ESCON konekcijama.

note: Type: select Description :sl5:
en: CTC write device:
bs: CTC uređaj za pisanje:

note: Type: boolean Description :sl5:
en: Do you accept this configuration?
bs: Da li prihvatate ovu konfiguraciju?

note: Type: boolean Description :sl5:
en: The configured parameters are:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}
bs: Podešeni parametri su:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}

note: Type: error Description :sl5:
en: No CTC or ESCON connections
bs: Nema CTC ili ESCON konekcija

note: Type: error Description :sl5:
en: Please make sure that you have set them up correctly.
bs: Molim provjerite da ste ih ispravno podesili.

note: Type: select Description :sl5:
en: Protocol for this connection:
bs: Protokol za ovu konekciju:

note: Type: select Description :sl5:
en: Device:
bs: Uređaj:

note: Type: select Description :sl5:
en: Please select the OSA-Express QDIO / HiperSockets device.
bs: Molim odaberite OSA-Express QDIO / HiperSockets uređaj.

note: Type: boolean Description :sl5:
en: The configured parameters are:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}
bs: Podešeni parametri su:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets
bs: Nema OSA-Express QDIO kartice / HiperSockets

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets were detected. If you are running VM please make sure that your card is attached to this guest.
bs: Nema OSA-Express QDIO kartica / HiperSockets nisu pronađene. Ako ste na VM molim provjerite da je vaša kartica priključena na ovog gosta.

note: Type: string Description :sl5:
en: Please enter a relative port for this connection.
bs: Molim unesite relativni port za ovu koneciju

note: Type: boolean Description :sl5:
en: Use this device in layer2 mode?
bs: Koristite ovaj uređaj u layer2 modu?

note: Type: boolean Description :sl5:
en: By default OSA-Express cards use layer3 mode. In that mode LLC headers are removed from incoming IPv4 packets. Using the card in layer2 mode will make it keep the MAC addresses of IPv4 packets.
bs: Standardno OSA-Express kartice koriste layer3 mod. U tom modu LLC zaglavlja su obrisana iz dolaznih IPv4 paketa. Koristeći karticu u layer2 modu će sačuvati MAC adrese IPv4 paketa.

note: Type: boolean Description :sl5:
en: The configured parameter is:
     peer  = ${peer}
bs: Podešeni parametar je:
     peer  = ${peer}

note: Type: string Description :sl5:
en: Please enter the name of the VM peer you want to connect to.
bs: Molim unesite naziv za VM peer sa kojim se želite povezati.

note: Type: string Description :sl5:
en: If you want to connect to multiple peers, separate the names by colons, e.g.  tcpip:linux1.
bs: Ako se želite povezati sa više peerova, odvojite nazive razmacima, npr. tcpip:linux1.

note: Type: string Description :sl5:
en: The standard TCP/IP server name on VM is TCPIP; on VIF it's $TCPIP. Note: IUCV must be enabled in the VM user directory for this driver to work and it must be set up on both ends of the communication.
bs: Standardni TCP/IP naziv za server na VM je TCPIP, na VIF naziv je $TCPIP. Pažnja: IUCV mora biti uključen u VM korisničkom direktoriju da bi ovaj driver radio i mora biti podešen na oba kraja komunikacijske veze.

note: Type: text Description Main menu item Translators: keep below 55 columns :sl5:
en: Configure the network device
bs: Podesite mrežni uređaj
