debian-installer_packages_po_sublevel1_da - en to da translation catalogue (27 entries)

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: ctc: Channel to Channel (CTC) or ESCON connection
da: ctc: Channel-to-Channel (CTC) eller ESCON-forbindelse

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: qeth: OSA-Express in QDIO mode / HiperSockets
da: qeth: OSA-Express i QDIO-tilstand / HiperSockets

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: iucv: Inter-User Communication Vehicle - available for VM guests only
da: iucv: Mellem-bruger kommunikations-transport - kun for VM-gæster

note: Type: select Description :sl5:
en: Network device type:
da: Netkorts-type:

note: Type: select Description :sl5:
en: Please choose the type of your primary network interface that you will need for installing the Debian system (via NFS or HTTP). Only the listed devices are supported.
da: Vælg typen på det primære netkort, som du vil bruge til at installere Debian-systemet fra (via NFS eller HTTP). Kun de viste enheder understøttes.

note: Type: select Description :sl5:
en: CTC read device:
da: CTC-læseenhed:

note: Type: select Description :sl5:
en: The following device numbers might belong to CTC or ESCON connections.
da: Følgende enhedsnumre kan tilhøre CTC- eller ESCON-forbindelser.

note: Type: select Description :sl5:
en: CTC write device:
da: CTC-skriveenhed:

note: Type: boolean Description :sl5:
en: Do you accept this configuration?
da: Vil du acceptere denne opsætning?

note: Type: boolean Description :sl5:
en: The configured parameters are:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}
da: De konfigurerede indstillinger er:
     læsekanal     = ${device_read}
     skrivekanal   = ${device_write}
     protokol      = ${protocol}

note: Type: error Description :sl5:
en: No CTC or ESCON connections
da: Ingen CTC- eller ESCON-forbindelser

note: Type: error Description :sl5:
en: Please make sure that you have set them up correctly.
da: Sørg for at du har sat dem korrekt op.

note: Type: select Description :sl5:
en: Protocol for this connection:
da: Protokol for denne forbindelse:

note: Type: select Description :sl5:
en: Device:
da: Enhed:

note: Type: select Description :sl5:
en: Please select the OSA-Express QDIO / HiperSockets device.
da: Vælg OSA-Express QDIO / HiperSockets-enhed.

note: Type: boolean Description :sl5:
en: The configured parameters are:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}
da: De indstillede parametre er:
     kanaler  = ${device0}, ${device1}, ${device2}
     port     = ${port}
     lag2     = ${layer2}

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets
da: Ingen OSA-Express QDIO-kort / HiperSockets

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets were detected. If you are running VM please make sure that your card is attached to this guest.
da: Fandt ingen OSA-Express QDIO-kort eller HiperSockets. Hvis du kører VM, så sørg for at dit kort er forbundet til denne gæst.

note: Type: string Description :sl5:
en: Please enter a relative port for this connection.
da: Angiv en port for denne forbindelse.

note: Type: boolean Description :sl5:
en: Use this device in layer2 mode?
da: Benyt denne enhed i lag2-tilstand?

note: Type: boolean Description :sl5:
en: By default OSA-Express cards use layer3 mode. In that mode LLC headers are removed from incoming IPv4 packets. Using the card in layer2 mode will make it keep the MAC addresses of IPv4 packets.
da: Som udgangspunkt benytter OSA-Express kort lag3-tilstand. I denne tilstand, fjernes LLC-hoveder fra indkommende IPv4-pakker. Hvis kortet benyttes i lag2-tilstand, bevares IPv4-pakkernes MAC-adresser.

note: Type: boolean Description :sl5:
en: The configured parameter is:
     peer  = ${peer}
da: Det opsatte parameter er:
     vært  = ${peer}

note: Type: string Description :sl5:
en: VM peer:
da: VM-vært:

note: Type: string Description :sl5:
en: Please enter the name of the VM peer you want to connect to.
da: Angiv navnet på den VM-vært (VM-peer), du vil forbinde til.

note: Type: string Description :sl5:
en: If you want to connect to multiple peers, separate the names by colons, e.g.  tcpip:linux1.
da: Hvis du vil forbinde til flere værter, kan du adskille navnene med kolonner, som f.eks. tcpip:linux1.

note: Type: string Description :sl5:
en: The standard TCP/IP server name on VM is TCPIP; on VIF it's $TCPIP. Note: IUCV must be enabled in the VM user directory for this driver to work and it must be set up on both ends of the communication.
da: Standardnavnet på en TCP/IP-server på VM er TCPIP, på VIF er det $TCPIP. Bemærk: IUCV skal være aktiveret i VM-brugermappen for at denne driver kan fungere og det skal sættes op i begge ender af kommunikationen.

note: Type: text Description Main menu item Translators: keep below 55 columns :sl5:
en: Configure the network device
da: Sæt netkortet op
