gl - en to gl translation catalogue (28 entries)

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: ctc: Channel to Channel (CTC) or ESCON connection
gl: ctc: Conexión canle a canle (CTC) ou ESCON

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: qeth: OSA-Express in QDIO mode / HiperSockets
gl: qeth: OSA-Express en modo QDIO / HiperSockets

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: iucv: Inter-User Communication Vehicle - available for VM guests only
gl: iucv: Vehículo de comunicación interusuario; só para hóspedes VM

note: Type: select Description :sl5:
en: Network device type:
gl: Tipo de dispositivo de rede:

note: Type: select Description :sl5:
en: Please choose the type of your primary network interface that you will need for installing the Debian system (via NFS or HTTP). Only the listed devices are supported.
gl: Escolla o tipo da interface primaria de rede, que vai necesitar para instalar o sistema Debian (por NFS ou HTTP). Só se admiten os dispositivos da lista.

note: Type: select Description :sl5:
en: CTC read device:
gl: Dispositivo de lectura CTC:

note: Type: select Description :sl5:
en: The following device numbers might belong to CTC or ESCON connections.
gl: Os seguintes números de dispositivo poden pertencer a conexións CTC ou ESCON.

note: Type: select Description :sl5:
en: CTC write device:
gl: Dispositivo de escritura CTC:

note: Type: boolean Description :sl5:
en: Do you accept this configuration?
gl: Acepta esta configuración?

note: Type: boolean Description :sl5:
en: The configured parameters are:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}
gl: Os parámetros configurados son:
     canle de lectura   = ${device_read}
     canle de escritura = ${device_write}
     protocolo          = ${protocol}

note: Type: error Description :sl5:
en: No CTC or ESCON connections
gl: Non hai conexións CTC nin ESCON

note: Type: error Description :sl5:
en: Please make sure that you have set them up correctly.
gl: Verifique que as ten correctamente configuradas.

note: Type: select Description :sl5:
en: Protocol for this connection:
gl: Protocolo para esta conexión:

note: Type: select Description :sl5:
en: Device:
gl: Dispositivo:

note: Type: select Description :sl5:
en: Please select the OSA-Express QDIO / HiperSockets device.
gl: Escolla o dispositivo OSA-Express QDIO / HiperSockets.

note: Type: boolean Description :sl5:
en: The configured parameters are:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}
gl: Os parámetros configurados son:
     canles        = ${device0}, ${device1}, ${device2}
     porto         = ${port}
     capa 2        = ${layer2}

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets
gl: Non hai tarxetas OSA-Express QDIO / HiperSockets

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets were detected. If you are running VM please make sure that your card is attached to this guest.
gl: Non se detectaron tarxetas OSA-Express QDIO / HiperSockets. Se está a executar VM asegúrese de que a súa tarxeta estea conectada a este hóspede.

note: Type: string Description :sl5:
en: Port:
gl: Porto:

note: Type: string Description :sl5:
en: Please enter a relative port for this connection.
gl: Introduza un porto relativo para esta conexión.

note: Type: boolean Description :sl5:
en: Use this device in layer2 mode?
gl: Desexa empregar este dispositivo en modo capa 2?

note: Type: boolean Description :sl5:
en: By default OSA-Express cards use layer3 mode. In that mode LLC headers are removed from incoming IPv4 packets. Using the card in layer2 mode will make it keep the MAC addresses of IPv4 packets.
gl: Por omisión, as tarxetas OSA-Express empregan o modo capa 3. Nese modo, as cabeceiras LLC elimínanse dos paquetes IPv4 entrantes. Se emprega a tarxeta en modo capa 2 hanse conservar os enderezos MAC dos paquetes IPv4.

note: Type: boolean Description :sl5:
en: The configured parameter is:
     peer  = ${peer}
gl: O parámetro configurado é:
     parceiro  = ${peer}

note: Type: string Description :sl5:
en: VM peer:
gl: Parceiro de VM:

note: Type: string Description :sl5:
en: Please enter the name of the VM peer you want to connect to.
gl: Introduza o nome do parceiro de VM ao que se quere conectar.

note: Type: string Description :sl5:
en: If you want to connect to multiple peers, separate the names by colons, e.g.  tcpip:linux1.
gl: Se quere conectarse a varios parceiros, separe os nomes con signos de dous puntos; por exemplo, tcpip:linux1.

note: Type: string Description :sl5:
en: The standard TCP/IP server name on VM is TCPIP; on VIF it's $TCPIP. Note: IUCV must be enabled in the VM user directory for this driver to work and it must be set up on both ends of the communication.
gl: O nome de servidor TCP/IP estándar de VM é TCPIP; en VIF é $TCPIP. Nota: IUCV ten que estar activado no directorio de usuario VM para que este controlador funcione, e debe estar configurado nos dous extremos da comunicación.

note: Type: text Description Main menu item Translators: keep below 55 columns :sl5:
en: Configure the network device
gl: Configurar o dispositivo de rede
