Debian-installer 1st-stage master file HR - en to hr translation catalogue (28 entries)

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: ctc: Channel to Channel (CTC) or ESCON connection
hr: ctc: Kanal u Kanal (CTC) ili ESCON povezivanje

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: qeth: OSA-Express in QDIO mode / HiperSockets
hr: qeth: OSA-Express u QDIO načinu / HiperSockets

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: iucv: Inter-User Communication Vehicle - available for VM guests only
hr: iucv: Međukorisničko komunikacijsko sredstvo - samo za VM goste

note: Type: select Description :sl5:
en: Network device type:
hr: Vrsta mrežnog uređaja:

note: Type: select Description :sl5:
en: Please choose the type of your primary network interface that you will need for installing the Debian system (via NFS or HTTP). Only the listed devices are supported.
hr: Odaberite vrstu vašeg glavnog mrežnog sučelja potrebnog za instalaciju Debian sustava (putem NFS-a ili HTTP-a). Podržani su samo navedeni uređaji.

note: Type: select Description :sl5:
en: CTC read device:
hr: Uređaj CTC čitanja:

note: Type: select Description :sl5:
en: The following device numbers might belong to CTC or ESCON connections.
hr: Sljedeći brojevi uređaja možda pripadaju CTC ili ESCON povezivanjima.

note: Type: select Description :sl5:
en: CTC write device:
hr: Uređaj CTC zapisivanja:

note: Type: boolean Description :sl5:
en: Do you accept this configuration?
hr: Prihvaćate li ovo podešavanje?

note: Type: boolean Description :sl5:
en: The configured parameters are:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}
hr: Parameteri podešavanja su:
     čitaj kanal  = ${device_read}
     zapisuj kanal = ${device_write}
     protokol      = ${protocol}

note: Type: error Description :sl5:
en: No CTC or ESCON connections
hr: Nema CTC ili ESCON povezivanja

note: Type: error Description :sl5:
en: Please make sure that you have set them up correctly.
hr: Pobrinite se da ste ih ispravno podesili.

note: Type: select Description :sl5:
en: Protocol for this connection:
hr: Protokol za ovo povezivanje:

note: Type: select Description :sl5:
en: Device:
hr: Uređaj:

note: Type: select Description :sl5:
en: Please select the OSA-Express QDIO / HiperSockets device.
hr: Odaberite OSA-Express QDIO / HiperSockets uređaj.

note: Type: boolean Description :sl5:
en: The configured parameters are:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}
hr: Parametri podešavanja su:
     kanali = ${device0}, ${device1}, ${device2}
     ulaz     = ${port}
     layer2   = ${layer2}

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets
hr: Nema OSA-Express QDIO kartica / HiperSocketa

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets were detected. If you are running VM please make sure that your card is attached to this guest.
hr: Nema otkrivenih OSA-Express QDIO kartica / HiperSocketa. Ako imate pokrenutu VM pobrinite se da je vaša kartica priključena kao gost.

note: Type: string Description :sl5:
en: Port:
hr: Ulaz:

note: Type: string Description :sl5:
en: Please enter a relative port for this connection.
hr: Upišite relativan ulaz za ovo povezivanje.

note: Type: boolean Description :sl5:
en: Use this device in layer2 mode?
hr: Koristi ovaj uređaj u layer2 načinu?

note: Type: boolean Description :sl5:
en: By default OSA-Express cards use layer3 mode. In that mode LLC headers are removed from incoming IPv4 packets. Using the card in layer2 mode will make it keep the MAC addresses of IPv4 packets.
hr: Po zadanome OSA-Express kartice koriste layer3 način. U tom načinu, LLC zaglavlja se uklanjaju iz dolaznih IPv4 paketa. Korištenje kartice u layer2 načinu će omogućiti zadržavanje MAC adresa u IPv4 paketima.

note: Type: boolean Description :sl5:
en: The configured parameter is:
     peer  = ${peer}
hr: Parametri podešavanja su:
     čvor  = ${peer}

note: Type: string Description :sl5:
en: VM peer:
hr: VM čvor:

note: Type: string Description :sl5:
en: Please enter the name of the VM peer you want to connect to.
hr: Upišite naziv VM čvora s kojim se želite povezati.

note: Type: string Description :sl5:
en: If you want to connect to multiple peers, separate the names by colons, e.g.  tcpip:linux1.
hr: Ako se želite povezati s više čvorova, odvojite nazive dvotočkama, npr.  tcpip:linux1.

note: Type: string Description :sl5:
en: The standard TCP/IP server name on VM is TCPIP; on VIF it's $TCPIP. Note: IUCV must be enabled in the VM user directory for this driver to work and it must be set up on both ends of the communication.
hr: Standardni naziv TCP/IP poslužitelja na VM je TCPIP, na VIF je $TCPIP. Napomena: IUCV mora biti omogućen u VM korisničkom direktoriju kako bi ovaj upravljački program radio i mora biti postavljen na oba završetka komunikacije.

note: Type: text Description Main menu item Translators: keep below 55 columns :sl5:
en: Configure the network device
hr: Podesi mrežni uređaj
