debian-installer - en to lt translation catalogue (28 entries)

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: ctc: Channel to Channel (CTC) or ESCON connection
lt: ctc: Channel to Channel (CTC) arba ESCON jungtis

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: qeth: OSA-Express in QDIO mode / HiperSockets
lt: qeth: OSA-Express inQDIO režime / HiperSockets

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: iucv: Inter-User Communication Vehicle - available for VM guests only
lt: iucv: Inter-User Communication Vehicle - tik VM svečiams

note: Type: select Description :sl5:
en: Network device type:
lt: Tinklo įrenginio tipas:

note: Type: select Description :sl5:
en: Please choose the type of your primary network interface that you will need for installing the Debian system (via NFS or HTTP). Only the listed devices are supported.
lt: Pasirinkite pagrindinio tinklo įrenginio tipą, kurį naudosite „Debian“ diegimui (per NFS ar HTTP). Tik nurodyti įrenginiai yra palaikomi.

note: Type: select Description :sl5:
en: CTC read device:
lt: CTC skaitymo įrenginys:

note: Type: select Description :sl5:
en: The following device numbers might belong to CTC or ESCON connections.
lt: Šitie įrenginių numeriai gali priklausyti CTC ar ESCON jungtims.

note: Type: select Description :sl5:
en: CTC write device:
lt: CTC rašymo įrenginys:

note: Type: boolean Description :sl5:
en: Do you accept this configuration?
lt: Ar sutinkate su šia konfigūracija?

note: Type: boolean Description :sl5:
en: The configured parameters are:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}
lt: Sukonfigūruoti parametrai:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}

note: Type: error Description :sl5:
en: No CTC or ESCON connections
lt: CTC ar ESCON jungčių nėra

note: Type: error Description :sl5:
en: Please make sure that you have set them up correctly.
lt: Įsitikinkite, kad teisingai jas nustatėte.

note: Type: select Description :sl5:
en: Protocol for this connection:
lt: Protokolas šiai jungčiai:

note: Type: select Description :sl5:
en: Device:
lt: Įrenginys:

note: Type: select Description :sl5:
en: Please select the OSA-Express QDIO / HiperSockets device.
lt: Prašau pasirinkti OSA-Express QDIO / HiperSockets įrenginį.

note: Type: boolean Description :sl5:
en: The configured parameters are:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}
lt: Sukonfigūruoti parametrai:
     kanalai      = ${device0}, ${device1}, ${device2}
     prievadas    = ${port}
     lygmuo2      = ${layer2}

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets
lt: OSA-Express QDIO kortų / HiperSockets nėra

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets were detected. If you are running VM please make sure that your card is attached to this guest.
lt: OSA-Express QDIO kortų ar HiperSockets įrenginių nerasta. Jei naudojate VM, įsitikinkite, kad Jūsų korta prijungta prie šio svečio (guest).

note: Type: string Description :sl5:
en: Port:
lt: Portas:

note: Type: string Description :sl5:
en: Please enter a relative port for this connection.
lt: Prašau įvesti santykinį portą (relative port) šiai jungčiai.

note: Type: boolean Description :sl5:
en: Use this device in layer2 mode?
lt: Ar naudoti šį įrenginį veiksenoje lygmuo2?

note: Type: boolean Description :sl5:
en: By default OSA-Express cards use layer3 mode. In that mode LLC headers are removed from incoming IPv4 packets. Using the card in layer2 mode will make it keep the MAC addresses of IPv4 packets.
lt: Paprastai OSA-Express kortos naudoja lygmuo3 veikseną. Šioje veiksenoje LLC antraštės pašalinamos iš įeinančių IPv4 paketų. Naudojant šias kortas lygmuo2 veiksenoje, IPv4 paketų MAC adresai lieka išsaugoti.

note: Type: boolean Description :sl5:
en: The configured parameter is:
     peer  = ${peer}
lt: Konfigūruotas parametras:
     peer  = ${peer}

note: Type: string Description :sl5:
en: VM peer:
lt: VM porininkas:

note: Type: string Description :sl5:
en: Please enter the name of the VM peer you want to connect to.
lt: Prašau įvesti VM porininko, su kuriuo norite susijungti, vardą.

note: Type: string Description :sl5:
en: If you want to connect to multiple peers, separate the names by colons, e.g.  tcpip:linux1.
lt: Jei norite susijungti su keliais porininkais, atskirkite jų vardus dvitaškiais, pvz.,  tcpip:linux1.

note: Type: string Description :sl5:
en: The standard TCP/IP server name on VM is TCPIP; on VIF it's $TCPIP. Note: IUCV must be enabled in the VM user directory for this driver to work and it must be set up on both ends of the communication.
lt: Standartinis TCP/IP serverio vardas VM sistemoje yra TCPIP, VIF sistemoje jis yra $TCPIP. Dėmesio: IUCV turi būti įjungtas VM vartotojų kataloge, kad ši tvarkyklė veiktų, ir ji turi būti sukonfigūruota abiejuose galuose.

note: Type: text Description Main menu item Translators: keep below 55 columns :sl5:
en: Configure the network device
lt: Tinklo konfigūravimas
