nb - en to nb translation catalogue (27 entries)

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: ctc: Channel to Channel (CTC) or ESCON connection
nb: ctc: Kanal-til-kanal (CTC) eller ESCON-samband

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: qeth: OSA-Express in QDIO mode / HiperSockets
nb: qeth: OSA-Express i QDIO-modus / HiperSockets

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: iucv: Inter-User Communication Vehicle - available for VM guests only
nb: iucv: Sambandsmiddel for kommunikasjon mellom brukere - bare tilgjengelig for VM-gjester

note: Type: select Description :sl5:
en: Network device type:
nb: Enhetstype for nettverk:

note: Type: select Description :sl5:
en: Please choose the type of your primary network interface that you will need for installing the Debian system (via NFS or HTTP). Only the listed devices are supported.
nb: Velg den typen hoved-nettgrensesnitt du vil trenge for å installere Debian-systemet (via NFS eller HTTP). Bare de listede enhetene er støttet.

note: Type: select Description :sl5:
en: CTC read device:
nb: CTC leseenhet:

note: Type: select Description :sl5:
en: The following device numbers might belong to CTC or ESCON connections.
nb: Følgende enhetsnumre kan høre til CTC eller ESCON-forbindelser.

note: Type: select Description :sl5:
en: CTC write device:
nb: CTC skriveenhet:

note: Type: boolean Description :sl5:
en: Do you accept this configuration?
nb: Godtar du disse innstillingene?

note: Type: boolean Description :sl5:
en: The configured parameters are:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}
nb: Parameterne i oppsettet er:
     lesekanal   = ${device_read}
     skrivekanal = ${device_write}
     protokoll   = ${protocol}

note: Type: error Description :sl5:
en: No CTC or ESCON connections
nb: Fant ingen CTC eller ESCON-forbindelser

note: Type: error Description :sl5:
en: Please make sure that you have set them up correctly.
nb: Sjekk at de er satt opp rett.

note: Type: select Description :sl5:
en: Protocol for this connection:
nb: Protokoll for denne forbindelsen:

note: Type: select Description :sl5:
en: Device:
nb: Enhet:

note: Type: select Description :sl5:
en: Please select the OSA-Express QDIO / HiperSockets device.
nb: Velg enhet for OSA-Express QDIO / HiperSockets.

note: Type: boolean Description :sl5:
en: The configured parameters are:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}
nb: Parameterne i oppsettet er:
     kanaler      = ${device0}, ${device1}, ${device2}
     port         = ${port}
     lag2         = ${layer2}

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets
nb: Fant ingen OSA-Express QDIO-kort eller HiperSockets

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets were detected. If you are running VM please make sure that your card is attached to this guest.
nb: Fant ingen OSA-Express QDIO-kort / HiperSockets. Hvis du kjører VM, pass på at kortet ditt er koblet til denne gjesten.

note: Type: string Description :sl5:
en: Please enter a relative port for this connection.
nb: Oppgi relativ port for denne forbindelsen.

note: Type: boolean Description :sl5:
en: Use this device in layer2 mode?
nb: Skal denne enheten brukes i kjøremåte lag2?

note: Type: boolean Description :sl5:
en: By default OSA-Express cards use layer3 mode. In that mode LLC headers are removed from incoming IPv4 packets. Using the card in layer2 mode will make it keep the MAC addresses of IPv4 packets.
nb: OSA-Express-kort bruker som standard kjøremåte lag3. Da fjernes LLC-hodene fra innkommende IPv4-pakker. Om kortet settes i kjøremåte lag2, så beholdes MAC-adressene i IPv4-pakkene.

note: Type: boolean Description :sl5:
en: The configured parameter is:
     peer  = ${peer}
nb: Oppsettsparameterne er:
     peer  = ${peer}

note: Type: string Description :sl5:
en: VM peer:
nb: VM-motpart:

note: Type: string Description :sl5:
en: Please enter the name of the VM peer you want to connect to.
nb: Skriv inn navnet på VM-tjeneren du vil koble deg til.

note: Type: string Description :sl5:
en: If you want to connect to multiple peers, separate the names by colons, e.g.  tcpip:linux1.
nb: Hvis du vil koble til flere tjenere, sett kolon mellom navnene, f.eks. «tcpip:linux1».

note: Type: string Description :sl5:
en: The standard TCP/IP server name on VM is TCPIP; on VIF it's $TCPIP. Note: IUCV must be enabled in the VM user directory for this driver to work and it must be set up on both ends of the communication.
nb: Standard tjenernavn for TCP/IP på VM er TCPIP, på VIF er det $TCPIP. Merk: IUCV må være slått på i VM-brukerkatalogen for at denne driveren skal virke, og det må være satt opp i begge ender av forbindelsen.

note: Type: text Description Main menu item Translators: keep below 55 columns :sl5:
en: Configure the network device
nb: Sett opp nettverksenheten
